ADEMCO 5817 PDF
Honeywell Security Intrusion and Communications, ADEMCO, AlarmNet, IntelliSense, Apex, FBII, electronic security systems, burglary alarms and fire alarms for. Installation manual for the Honeywell wireless three-zone sensor. For help installing your , call The Honeywell is a wireless three zone sensor. Unlike other Honeywell wireless window and door sensors, the does not have an internal reed switch.
|Published (Last):||23 August 2017|
|PDF File Size:||2.38 Mb|
|ePub File Size:||19.51 Mb|
|Price:||Free* [*Free Regsitration Required]|
Except in the case of the position 4 ON setting, the Auxiliary loops are not affected by. Attach the case back to the mounting plate 58177 sliding the keyhole slots in the case back down. The two Auxiliary Loops are closed-circuit, with a nominal response time of mSec.
Honeywell ADEMCO 5817 Installation And Setup Manual: Wiring Connections; Specifications
By pressing ‘print’ button you will print only current page. For UL installations, no contact in any of the loops may be more than 3 feet from the transmitter.
Seller does not represent that the product s it sells may not be compromised or circumvented; that the product s will adeemco any personal injury or property adecmo by burglary, robbery, fire or otherwise; or that the product s will in all cases provide adequate warning or protection.
Replace battery only with: Surface wiring should enter via the thin “breakout” area provided in. Although two holes are provided in the unit that would permit mounting directly to a surface holes “A” in Diagram 2it is recommended that the mounting plate be used, as described below, for ease in removing the unit for servicing should it become necessary.
Complain wrong Brand wrong Model non readable. The unit may, however, be installed in any direction, as long as the relationship of the unit to its mounting plate is maintained. With the battery still not inserted, connect the loop wiring to the unit’s terminals see Diagram 2.
While the transmitter is being enrolled by the control, all DIP switch positions should. Dispose of used batteries promptly.
Honeywell ADEMCO 3 Point Wireless Transmiter | eBay
Don’t have an account? Recommendations must be included for a specific. If a contact loop is not to be used, no connection is needed across its terminals. Disengage the supplied mounting plate from the unit by avemco the blade of a small screwdriver into the locking tab release window see Diagram 2 and pressing it against the case locking tab see Diagram 1 while sliding the plate downward along the case back. Risk of fire, explosion, and burns. Regular maintenance and inspection at least annually by the installer and frequent testing by.
Page of 2 Go. Got it, continue to print. Disengage the supplied mounting plate ademdo the unit by inserting the blade of a small. The Multi-Point Universal Transmitter may have three contact loops connected to it. For UL installations with fire zones, the position 4 ON setting must not be used.
When a satisfactory location is found, remove the battery and proceed with installation. The description that follows assumes that the unit will be mounted as shown in the diagrams.
The has its own unique identification codes permanently assigned during manufacture.
If concealed wiring is to be used, feed the wires through the concealed wiring entry hole at. Don’t show me this message again.
Mounting For proper orientation of the unit in relation to its wall mounting plate and the loop wiring, read all of this section before installing the unit. Do not recharge, disassemble, heat above. For this application, the alignment guide strip along one edge of the plate serves no function and may be broken away, if desired.
Wiring Connections; Specifications – Honeywell ADEMCO Installation And Setup Manual [Page 2]
adfmco Customer understands that a properly installed and maintained alarm system may only reduce the risk of a burglary, robbery, fireor other axemco occurring without providing an alarm, but it is not insurance or a guarantee that such will not occur or that there will be no personal injury or property loss as a result. Each loop transmits a unique ID code to a wireless system receiver connected to the system control panel.
No increase or alteration, written or verbal, of the obligations of this Limited Warranty is authorized. Seller shall have no obligation under this Limited Warranty or otherwise if the product s is altered or improperly repaired or serviced by anyone other than Honeywell factory service. Observe correct polarity and insert the battery provided into the battery holder see. It is not necessary to program the transmitter IDs during installation.
Enter text from picture: The should be treated as “RF” i. If concealed wiring is to be used, feed it through the slot in the case back but do not connect. This warranty replaces any previous warranties and is the only warranty avemco by Seller on this product s. A built-in cover tamper switch is activated when the cover is removed.
Add to my manuals Add. The open slot at the other end of the unit cannot be used as a asemco pry-off. Comments to this Manuals Your Name. Remove the transmitter’s cover if not already off as described in Mounting Step 1. Install the mounting plate, with its case holding posts pointing up in this exampleademo the.